IGBT Module Applications in EV Charging Piles: A Panorama of Power Device Selection from PFC to DC-DC
Introduction: IGBT modules are the core devices in the power conversion chain of DC fast charging piles. In 2025, the global revenue scale of IGBTs for charging piles is approximately RMB 1.129 billion, and it is expected to approach RMB 3.337 billion by 2032, with a compound annual growth rate of about 16.4%. The power system of a DC fast charging pile consists of two major power stages: the PFC rectifier stage and the DC-DC conversion stage. IGBT modules play different roles in these two stages, and the selection strategies are completely different.
1. Power Architecture of DC Charging Piles: Why IGBT Modules Are the Core
The power module of a DC charging pile mainly consists of a two-stage structure. The front-end AC/DC (PFC stage) converts 380-415VAC from the grid into a stable DC link voltage of approximately 800V; the rear-end DC-DC stage converts the 800V DC link voltage into a DC voltage suitable for the EV battery.
In this architecture, IGBT modules undertake two key tasks: in the PFC stage, they achieve power factor correction, reduce harmonics, and improve power quality; in the DC-DC stage, they achieve a wide range of DC voltage output to meet the charging needs of different types of batteries.
The power level of charging pile power modules is gradually increasing from 20kW/30kW to 40kW/50kW and above. Modular stacked power architectures are commonly adopted in the industry, which facilitates product reuse across different power levels and enables large-scale procurement and rapid delivery. This provides a long-term demand basis for IGBT modules in mature solutions.
2. PFC Stage: Device Selection for High Switching Frequency Scenarios
Mainstream Topology: Vienna PFC
The three-phase Vienna PFC is the most commonly used topology for AC/DC converters in DC charging pile power modules. This topology controls the charging and discharging of the PFC inductor by controlling the on/off of Sa, Sb, and Sc. The PF value of the PFC converter is close to 1, and the three phases are balanced. Each phase includes a bidirectional switch, connected by switches with a common source. The two switches share one drive signal, so there is no bridge-arm shoot-through problem, no dead time is required, and the difficulty of control and driving is reduced.
Switching Frequency and Device Requirements
The switching frequency of PFC applications in charging piles is generally around 20kHz to 50kHz, and some high-frequency solutions can reach above 50kHz. The higher the switching frequency, the higher the proportion of switching losses. Therefore, the PFC stage places extremely high requirements on the switching speed and loss characteristics of IGBTs.
Shanghai Belling's 80A/650V IGBT product BLG80T65FDK7, launched for DC charging pile power modules, adopts third-generation micro-trench multi-layer field-stop technology and is suitable for high-frequency applications of 50kHz and above. Its Eon/Eoff/Etotal values are reduced by approximately 6.7%/6.8%/6.8% respectively compared with competing products, and the reverse recovery charge Qrr is reduced by approximately 18%, which helps reduce EMI and improve efficiency.
Key Points for PFC Stage IGBT Selection
3. DC-DC Stage: Module Package Selection for High-Power Scenarios
The DC-DC stage is the second stage of power conversion in charging piles. It is responsible for isolating and converting the 800V DC voltage output by the PFC stage into the voltage required by the battery. This stage has higher power and places higher requirements on current capability and heat dissipation. IGBT modules are the more common choice.
Mainstream Package Forms
The EasyPACK™ series is a common choice for the DC-DC stage of charging piles. Infineon's EasyBRIDGE™ rectifier module DDB2U60N12W3RF_C39 is a 1200V, 60A specification, using trench-gate field-stop technology IGBT7 and CoolSiC™ Schottky diode G5 chips. The module height is only 12mm, stray inductance is extremely low, an NTC temperature sensor is integrated, and PressFIT press-fit pin technology is supported. The EasyPACK™ series covers the 600V/650V/1200V voltage range and currents from 20A to 200A, suitable for industrial frequency conversion, photovoltaic inverters, charging piles, heat pumps, and other scenarios.
The 62mm package module is suitable for higher-power DC-DC conversion scenarios, covering the 1200V, 25A to 800A current range.
The EconoPACK™ series is also a commonly used package form for charging pile power modules. Together with EasyPACK and 62mm modules, it forms the mainstream package matrix for charging pile IGBT modules.
Key Points for DC-DC Stage IGBT Selection
4. Leading Enterprise Solutions: Infineon's Power Semiconductor Layout for Charging Piles
Infineon has the most complete layout in the field of charging pile IGBT modules. In its cooperation solution with Shenzhen UUGreenPower, by providing a full set of power semiconductor solutions including CoolMOS™, TRENCHSTOP™ IGBT, CoolSiC™ MOSFET, and EiceDRIVER™ drivers, it fully empowers the technological upgrade of UUGreenPower's new-generation 40kW/60kW independent air duct charging modules, liquid-cooled charging modules, and V2G vehicle-to-grid interaction solutions. By adopting the CoolSiC™ silicon carbide solution, UUGreenPower's charging module efficiency has been increased to above 97.5%.
Infineon also cooperated with Weiguang Energy to develop solid-state transformer products for energy storage systems and charging piles based on 1200V TRENCHSTOP™ IGBT7 and CoolSiC™ MOSFET G2 technology, with maximum efficiency exceeding 98.5%.
Among domestic manufacturers, Shanghai Belling has launched 650V/80A IGBT products and SiC MOS product lines, covering the PFC stage and DC-DC stage requirements of DC charging pile power modules.
5. Technology Trends: Coordinated Evolution of IGBT and SiC in Charging Piles
SiC Is Accelerating Penetration in High-Power Charging Scenarios
As charging piles develop toward high power and high voltage, silicon carbide devices are accelerating penetration. In practical applications, using silicon carbide modules in charging piles can increase output power by nearly 30% and reduce losses by 50%; in power conversion modules, after replacing IGBTs with SiC MOSFETs, efficiency can be increased from 95% to above 97%, and power density can reach 60W/in³.
The national standard for charging pile energy efficiency was implemented in November 2025. The first-level energy efficiency weighted efficiency requirement is above 96.5%, forcing charging module efficiency to exceed 97%, which further accelerates the introduction of SiC devices. According to the "15th Five-Year Plan," by 2030, the total number of charging infrastructure will exceed 40 million, with about 300,000 high-power charging facilities. High-power charging and vehicle-to-grid interaction are becoming another large-scale application scenario for SiC after EV main-drive inverters.
IGBT Will Still Occupy the Mainstream Power Segment for a Long Time
Although SiC is growing rapidly, IGBT in the charging pile market shows an evolution path of "stable volume and structural differentiation": the mainstream power segment maintains a large volume and, with mature processes, good robustness, and supply chain scale advantages, is widely used in key links such as rectification and power conversion; the high-end power segment forms a pattern of parallel coexistence with SiC.
Hybrid Solutions Become Mainstream During the Transition Period
Infineon's EasyPACK™ 2B module integrates both CoolSiC™ MOSFET 1200V and TRENCHSTOP™ IGBT7 1200V technologies in the same package, providing charging pile designers with a flexible device combination solution. This hybrid solution achieves a better balance between cost and efficiency.
Conclusion
The core logic of IGBT module application in charging piles is selection by stage: the PFC stage prioritizes high switching frequency and low switching losses, while the DC-DC stage prioritizes high current capability and heat dissipation performance. In terms of package selection, EasyPACK™, EconoPACK™, and 62mm modules are the three mainstream forms. With the advancement of high-power charging and V2G vehicle-to-grid interaction, SiC is accelerating penetration, but IGBT, with its mature process and cost advantages, will still maintain long-term demand in the mainstream power segment. For charging pile designers, the key is to find the optimal balance among voltage class, current capability, switching frequency, and heat dissipation scheme.